Why a modern, autonomous UV-C robot is a realistic alternative to hydrogen peroxide vapour (HPV) fogging for routine terminal disinfection, and what hospitals gain by making the switch.
At a glance
Fogging is microbiologically effective, but it takes rooms out of use for hours. Omnia® delivers validated efficacy with a fraction of the downtime.
¹ de Jager et al. (2026). ² Havill et al. (2012).
Introduction
Healthcare-associated infections (HAIs) remain one of the largest patient-safety challenges in European hospitals. Each year an estimated 4.3 million patients in EU/EEA acute care hospitals acquire at least one HAI, and on average 7.1% of hospitalised patients are affected (ECDC, 2024). HAIs prolong hospital stays, increase costs and contribute to antimicrobial resistance.
Contaminated surfaces play a recognised role in transmission: a patient admitted to a room previously occupied by a patient colonised or infected with certain pathogens has a higher risk of acquiring them. Conventional manual disinfection depends on the operator, which is why hospitals increasingly add “no-touch” automated room disinfection after routine cleaning (Otter et al., 2013; Weber et al., 2016). The two main no-touch technologies are hydrogen peroxide vapour (HPV) fogging and ultraviolet-C (UV-C) light.
The challenge
HPV fogging is microbiologically effective, including against bacterial spores (Havill et al., 2012). Its limitations are mainly practical: time, preparation, safety measures and running costs.
The solution
UV-C light inactivates micro-organisms by damaging their DNA and RNA. The added value of UV-C after routine cleaning is supported by clinical evidence: in the multicentre, randomised BETR Disinfection study, adding UV-C to standard terminal cleaning reduced acquisition of the target organisms among subsequent room occupants by 30% (Anderson et al., 2017). Omnia® builds on this evidence with autonomous navigation and dose-controlled disinfection.
Why Omnia® stands out
In an independent study by the Institute of Biology Leiden, Omnia® achieved log reductions of more than 7 for E. coli, more than 5 for P. putida and more than 7 for B. subtilis, meeting the 5-log criteria of the US EPA and BS 8628:2022 for all organisms tested (de Jager et al., 2026).
Cycle time follows a simple rule of thumb of about 15 seconds per m² per intensity level. For a room of about 53 m² this is approximately 13 minutes (Quick), 27 minutes (Normal) or 40 minutes (Deep), plus 4 to 7 minutes of set-up (de Jager et al., 2026).
UV-C acts in direct line of sight, and areas that are not directly lit receive a lower dose; this is a known limitation of static UV-C devices (Havill et al., 2012). Omnia® moves autonomously through the room with 360° coverage from eight lamps, as close as 15 cm to surfaces. At the same duration, moving disinfection outperformed static UV-C, especially at a partially shadowed location (de Jager et al., 2026).
Four dose profiles, from Quick for routine turnover to Deep for high-risk and spore-forming pathogens and Custom (40 to 100 mJ/cm²) for outbreak situations.
Each cycle ends with an automatic disinfection report, including a dose heat map of the room and the expected log reduction per pathogen. In the Leiden study, actual results were equal to or better than reported (de Jager et al., 2026).
No chemicals, no residue and no aeration phase. The room can be used again as soon as the cycle has finished.
Direct exposure to UV-C is harmful to skin and eyes, so Omnia® only operates in unoccupied rooms. Door guards secure the entrances, visual alarms show that a cycle is running and staff start and monitor the robot from a tablet outside the room. No sealing of doors or ventilation is required.
No chemical consumables, and a novice operator was ready to start within 4 to 7 minutes (de Jager et al., 2026).
Like fogging, Omnia® is used after routine cleaning. UV-C disinfects surfaces but does not remove dirt, so manual cleaning remains the first step.
Comparative analysis
| Feature | Ryberg Omnia® UV-C | HPV fogging |
|---|---|---|
| Cycle time per room | approx. 13 to 40 min for about 53 m², depending on dose setting, plus 4 to 7 min set-up¹ | approx. 2.5 hours on average (140 to 177 min)² |
| Room preparation | No sealing of doors or ventilation | Sealing of doors and ventilation, leak monitoring |
| Re-entry | Immediately after the cycle | After aeration to a safe concentration |
| Active agent | UV-C light, no chemicals | Hydrogen peroxide (consumable) |
| Exposure risk and control | UV-C is harmful on direct exposure; controlled by operation in unoccupied rooms, door guards and remote control | Hazardous vapour; controlled by sealing, monitoring and aeration |
| Shadowed areas | Reduced by autonomous movement and 360° coverage | Vapour distributes through the sealed room |
| Operation | Minimal training; started and monitored remotely | Trained operator required |
| Documentation | Automatic dose report with heat map per cycle | Cycle log; efficacy verified separately |
| Running costs | No chemical consumables | Hydrogen peroxide per cycle, operator training |
¹ de Jager et al. (2026). ² Havill et al. (2012), mean HPV cycle time per patient room. Times for other rooms depend on room size and selected dose.
Conclusion
Fogging is effective, but it takes rooms out of use for hours and requires sealing, aeration, chemicals and trained operators. Ryberg Omnia® offers hospitals a practical alternative for routine terminal disinfection: independently validated efficacy above the 5-log standard, cycles measured in minutes instead of hours, no chemicals, immediate re-entry and a documented dose for every room.
For hospitals that want to strengthen infection prevention while improving room turnover and reducing the operational burden on staff, Omnia® is a well-founded next step. Ryberg is happy to demonstrate Omnia® in your own facility.
References
Compare it with your current fogging routine, room by room.